Zack – Page 19 – FLC Innovation

02Jun 2016

Happiness Is A Full Parts Bin

by Zack ⋅ 1 Comment

The dust shoe I mentioned in a previous post for the X-Carve printed nicely over the weekend, and today I had some time to assemble it and get it installed.

The instructions called for a strip of vinyl to use as the skirt for the shoe. It pays to be obsessive about hoarding things that might contribute to projects, and I remembered that I had squirreled away several feet of multicolored vinyl, from where I can’t remember. I fished around in the parts area, which is filled with old printers, pieces of foam and plastic, metal brackets, and the like, and found it. Though there’s nothing in the photo for scale, but suffice it to say that the crumpled pile below represents A LOT of vinyl – probably 8′ or 10′ x 4′ of it?

I cut a strip from the bright yellow scrap, and installed it on the shoe, then installed the shoe on the router. Tomorrow I hope to have time to actually turn the machine on (in router mode, rather than in plotter mode) and see how it works!

Happiness is a full parts bin.

28May 2016

CNC + 3D Printing + Streaming Video

by Zack ⋅ 3 Comments

Max and I spent some time in the shop this afternoon, brainstorming Chemistry activities that will make use of the new X-Carve and vinyl cutter, and working on the new Ultimaker 2 Extended+ that arrived the other day. After some tweaking, we got the printer running, and decided to print this Dewalt DWP611 Thread-On Dust Shoe from Thingiverse (CC BY Noah Mackes). Up until now, we’ve been using the X-Carve as a plotter, but Marisa Sayago (Professor, Art) and I have been talking about some printmaking ideas that involved cutting and engraving, hence the need for the dust shoe.

The printer reported that the job was going to take 17 hours, so Max and I decided to set up a webcam and do some R&D on Open Broadcaster Studio, which I have been considering using for the live fishcam that will be part of the aquaponics project. We installed the software, plugged in the camera, put in the YouTube live streaming information, and it all worked perfectly right out of the gate.

By the time I got home, the camera had slipped or been knocked sideways, but the print is still visible!

I’ve been working with technology for many years, but the idea that I can relatively easily monitor from home a 3D print job of a part I need and was able to download for a CNC machine that can be used to support (among other things) hands-on student activities in Chemistry and Art, while simultaneously testing a software program and a streaming service for another project that combines Library, Chemistry, Biology, Theater Arts, fish, and plants is, frankly, pretty neat.

I almost forgot – I made a Voronoi Totoro on the X-Carve (in plotter mode):

21May 2016

X-Carve as Drawing Machine

by Zack ⋅ 4 Comments

We don’t have dust collection set up just yet, so running the router on the new X-Carve is a messy prospect. Max Mahoney (Chemistry) has ideas about using the machine for some copper etching labs, so we set about adapting it for a pen. We fairly quickly found a model of a 3D printable pen holder for the X-Carve (CC BY Duane Northcutt), and printed it out, tapping the holes for M4 screws. PLA surprisingly seems to hold a thread fairly well.

After several experiments with various pens, we were able to successfully draw a pleasing circular Voronoi tessellation using an orange Vis-a-Vis overhead transparency marker on 12″ x 12″ piece of foam core board.

The whole thing took about 36 minutes to complete. Here’s a short, mesmerizing (to me anyway) video of the CNC hard at work.

21May 2016

Vinyl Cutter = Sweet Signage

by Zack ⋅ 4 Comments

A couple of days ago, in the midst of the x-carve build, a new vinyl cutter arrived.

I had seen a lab full of them at a recent visit to Portland Community College’s MakerSpace, and Gregg Meyer (coordinator of the space and all-around enthusiastic and generous person) mentioned that they were an inexpensive and useful bit of gear, and quite accessible to makers at all skill levels.

We needed a project to put the new machine through its paces, so we decided to label the experimental aquaponics system. The software that comes with the machine is pretty straightforward, and we were able to design and cut out some signage relatively quickly. After cutting out the letters, we realized we didn’t have any transfer paper, so we made do with blue painter’s tape.

The transfer went off without a hitch!

17May 2016

X-Carve Build Day, Part 3

by Zack ⋅ 3 Comments

The build crew met again this morning for the third and final X-Carve build day.

Finished up the work area, z-axis, drag chains and final wiring…

After a few perplexing challenges, especially regarding the mounting of the y-axis drag chain, we were able to finish the build, fire the machine up, and make our first test cuts!

All in all, a very satisfying build, and we learned a lot. For anyone looking to build an X-Carve, I would advise double-checking the forums at Inventables if you run into inconsistencies in the instructions – there aren’t many, but there are one or two differences between the current shipping kit and the videos and build instructions online. I would also advise using the GrabCAD models. We ignored these until the very end, but they proved very useful when figuring out the drag chain mounting, and I wish we had checked them sooner – we pretty much ignored them until the very end of the build.

Potato quality video – I was holding the vacuum in one hand and trying to shoot video with the other, and apparently the iPhone didn’t know upon what to focus):

In the next couple of days, I hope to get the dust extraction situation worked out, and to extend the XYZ wiring so that the power supply can live a little farther from the machine.

X-Carve Build Day, Part 1

X-Carve Build Day, Part 2

Build photos

14May 2016

X-Carve Build Day, Part 2

by Zack ⋅ 5 Comments

Back to the build… After a successful build day last week, we started Build Day 2 with some goodies, including Diane’s home-roasted coffee, egg and cheese sandwiches, homemade scones, muffins and pastries:

Today didn’t go quite as smoothly as I’d hoped, mostly because I mistakenly believed that one of the rails had not been tapped, which triggered a mad dash to the local hardware store for a tap and die set that turned out to be unnecessary. My mistake transformed into a learning experience and some skill building, so it wasn’t all bad:

We were able to get the Z-axis assembled:

And all of the motors wired:

We’re planning on finishing up the project after the weekend, and then we’ll get to carving!

Additional photos…

07May 2016

X-Carve Build Day, Part 1

by Zack ⋅ 6 Comments

Spent much of today with a few of my primary collaborators: Diane Carlson (bottom left – she of Making Social Change fame), Max Mahoney (top left – he of molecule making and molecular visualizer fame), Jennifer Kraemer (top right, she of various making in ECE projects like the building system interoperability activity) and me (bottom right) putting together the new X-Carve.

Jennifer fine-tuning a pulley for the Y axis:

Diane and Max strategizing:

We ended the day with most of the structure built, and will meet again next week to tackle the belts and electronics.

More photos from the X-Carve build day…

05May 2016

Soak a Professor

by Zack ⋅ Leave a Comment

Students from the Math and Engineering Club worked in the Innovation Center this morning to prepare for a “Soak a Professor” event.

Preparing the target:

The siege engines, ready to siege:

I didn’t get any shots from the actual event, but suffice it to say that the professors involved were indeed soaked.

04May 2016

A Lesson in Interoperability…

by Zack ⋅ 2 Comments

Students in Jennifer Kraemer’s ECE 312 – Child Development class had the opportunity to explore interoperability of proprietary building systems, with a little help from 3D printed interface pieces.